DATASHEET OF HT12D PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. HT12DDIP Ic-remote Control Decoder Features. Operating voltage: V~12V Low power and high noise immunity CMOS technology Low standby current. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit.

Author: Zukazahn Shaktisar
Country: Laos
Language: English (Spanish)
Genre: Relationship
Published (Last): 11 October 2012
Pages: 18
PDF File Size: 10.6 Mb
ePub File Size: 13.14 Mb
ISBN: 521-3-80199-778-8
Downloads: 4969
Price: Free* [*Free Regsitration Required]
Uploader: JoJojar

They can also be connected to LED to physically view the received data. Thus this helps in setting up oscillations in the IC. Valid transmission; active high.

So if you are working on a project which has to transmit a 4-bit data from one end to other either by daatsheet or wireless then this IC pair will be best suited for you. Choosing Motor For Robots.

ht12e ht12d datasheet – ht12e ht12d datasheet

If any valid data is received they can be obtained from these four pins. This is an CMOS logic integrated circuit encoder. Arduino based GPS receiver.

A valid transmission in indicated by a hr12d signal at VT pin. This pin will go high when a data is received.

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. It is mainly provided to interface RF dataasheet infrared circuits. Submitted by admin on 27 October The IC has a built in oscillator. Gone are the days when we used to use wires to connect two devices to establish a communication path. This pin powers the IC should use only 5V. This oscillator can be used by dxtasheet these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received.

  DIVYA PRABANDHAM PDF

Skip to main content.

HT12D Decoder IC

This site uses cookies. These pins are generally shorted by a resistor. For decoding a datashwet the IC will requires an oscillatorluckily this IC has one in-built.

This IC hasmany applications in short range remote controlling. At low signal data is transferred via antenna and received by Receiver IC which then decodes it to original parallel data. Generally a resistor of value 51 KOhms can be used. In simple terms, HT12D converts the serial input into parallel outputs. These two ICs together form an Encoder and Decoder pair. An LED can also be connected across this terminal to indicate output.

This pin outputs the parallel data serially.

The data on 4 bit latch type output pins remain unchanged until new is received. The input data code is decoded when no error or unmatched codes are found. Whenever an active low signal is applied at its TE pin then only the parallel data gets transferred serially at the output, otherwise the IC is in high impedance state.

  KETTLEBELL RKC PDF

The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. This high-density System-in-Package SiP integrates controller, power switches, and support components. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. I am now going to tell you about to control a certain robot wirelessly rather than using wires.

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

This oscillator can be used by connecting these two pins through a 1M Resistor. We should set the bits in same pattern on Ht1d and Decoder IC to pair them. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits.

Choosing Battery for Robots.