HT12E DATASHEET IN PDF

The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 2 12 series of encoders. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Arazilkree Gat
Country: Solomon Islands
Language: English (Spanish)
Genre: Photos
Published (Last): 16 December 2011
Pages: 280
PDF File Size: 10.86 Mb
ePub File Size: 17.4 Mb
ISBN: 862-9-98773-466-9
Downloads: 33942
Price: Free* [*Free Regsitration Required]
Uploader: Mazulkree

Choosing Battery for Robots. These are the 8-bit address bits, which is used to protect your data. The primary function of HT12E is to encode a bit and send it out through the output pin. These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address datasgeet to ground.

HT12E Encoder IC

datasneet Simply put, HT12E converts the parallel inputs into serial output. Supply voltage; 5V 2. Interface GPS with Arduino.

The IC is has a wide range of operating voltage from 2. Choosing Motor For Robots. Skip to main content. HT12E has a transmission enable pin which is active low.

What is Web Browser. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

  7805A JRC PDF

These 12 bits are divided into 8 address bits and 4 data bits. Submitted by admin on 30 October They are paired with 2 12 series of decoders for use in remote control system applications. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter.

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Transmission enable; active low. This pin has to be connected to Ground 0V to enable the Transmission.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

Can range from 2. HT12E is an encoder integrated circuit of 2 12 series of encoders. These two ICs together form an Encoder and Decoder pair. Connected to the Ground of circuit.

The Encoded 12 bit output data can be obtained from this pin. The encoded bit can be obtained from the Dout pin pin The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. It is mainly used in interfacing RF and infrared circuits. They can also be connected to switches to manually send and receive data. Arduino dtaasheet GPS receiver. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable.

  A COMMUNICATIVE GRAMMAR OF ENGLISH LEECH SVARTVIK PDF

This oscillator can be used by connecting these two pins through a 1M Resistor.

You can know to set up the HT12D after this from here. If datasheet want security you can connect any of the 8 pins to 5V to make it high. It is very important that your Decoder should also have this same address for them to talk to each other. TL — Programmable Reference Voltage.

As soon as TE returns to high, the encoder output completes its final cycle and then stops. This cycle is repeated as long as TE is kept low. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

Interface SD Card with Arduino. SPI Module of Arduino. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. The IC has a built in oscillator.