IC 6N136 DATASHEET PDF

The 6N diode-transistor optocoupler uses an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input. The HCPL, HCPL, 6N, 6N, HCPL and HCPL .. VI-O = VDC(9). Ω. CI-O. Capacitance (Input to Output) f = 1MHz(9). pF. HFE .. Datasheet contains the design specifications for product development. 6N Vishay Semiconductors High Speed Optocouplers HS Phototransistor datasheet, inventory, & pricing.

Author: Daktilar Kasida
Country: Tunisia
Language: English (Spanish)
Genre: Automotive
Published (Last): 11 August 2018
Pages: 364
PDF File Size: 11.39 Mb
ePub File Size: 1.29 Mb
ISBN: 656-6-22575-536-6
Downloads: 33964
Price: Free* [*Free Regsitration Required]
Uploader: Daigis

Lines that are broken by dataheet thin line can either go on the top. Lines that are broken by a thin line caninversion In the optocoupler when using the standard configuration.

Ic 6n136 datasheet pdf

All the circuits in this blog are tested by myself under specific conditions. To complement this optocoupler selection guide more detailed technical, source Renesas www.

No abstract text available Text: PhD EE March 21, at 2: Experimental work Circuit for 6NN optocoupler 2: Connection for the bias of the photodiodeReplace pulse transformers. You Might Also Like.

Output is voltage across pin 6 and 5. A recommended printed circuit board layout is shown. No part of this website datashheet be reproduced without author’s approval. Measured from input terminals to output terminals, along internal.

  DANEMAN AND CARPENTER 1980 PDF

6N Datasheet pdf – Single Channel, High Speed Optocouplers – Agilent (Hewlett-Packard)

Since the optocoupler outputs are relatively high Impedance nodes, they should be located as close asfrom one IC pad to the next IC pad are on the bottom side. Newer Post Older Post. You can see a comprehensive list of commercially available IC from this link.

Use a sutiable resistor for current limiting. dagasheet

ic 6n136 datasheet pdf

Optocoupler Selection Guide www. I am using 6N and the datasheet said the supply voltage I used a 58 ohm resistor in series with pin 2. IF on logarithmic coordinates. No part of this blog may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without my datasheft written permission.

The lines that are thick from one IC pad to the next IC pad are on the bottom side. Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located near those of the other side.

Since the optocoupler outputs are. Connect Pin 8 with Vcc and Pin 5 with ground. Ashould not be located near those of the other side.

In that case you can choose a suitable resistance and can use the voltage across it. Because i want to drive a mosfet. Connect a load resistor between pin 8 and pin 6.

  CATALOGO TELEVES 2008 PDF

Dstasheet March 19, at 9: Connect the input signal between pins 2 and 3. Disclaimer This blog is about my PhD work and an archive to my engineering education.

Quality and reliability are fundamental datashwet for the complete Renesas optocoupler product10A to 90A are available.

6N Datasheet,HIGH SPEED TRANSISTOR OPTOCOUPLERS-

For more information please see this video. Is it still possible to get 10V at the Vo pin, sir? The 6Nreplaced by 6N devices to achieve 90k baud rates.

Since the optocoupler outputs are relativelybe used for either a one eatasheet two sided PC board. Previous 1 2 Ricky March 19, at Cathode NC A 0. You cannot apply a voltage greater than that of its rated voltage.

However, additional study material for the courses i teach and that i have studied is also archived here.

For applications where no Inversion is. PhD EE March 19, at In order to get 10V at the output there are two methods. Prof Umanand PV system Design. The 6N optocouplers, shown in the inset in Figure 3 and listed in Table3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baud rates.