KEMA 08 ATEX IECEx KEM Features. □ Wide temperature range . □ PLEXO connection system, cold-applied connection and shrinkable tubing. EU-Type Examination Certificate Number: KEMA 98ATEX X are recorded in confidential test report number NL/KEM/ExTR/ KEMA 05ATEX X. PTB 02 ATEX X. Electrical KEMA 08ATEX SEV 10 ATEX SEV 10 ATEX SEV 10 ATEX SEV 10 ATEX.
|Published (Last):||16 June 2009|
|PDF File Size:||15.67 Mb|
|ePub File Size:||7.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
In conjunction with the PA00 touch panel, the GW32 also establishes communication between a higherranking 0110 system and the MPCnet. Silicone heater plate for control cabinets SSM, 0101 Two jackets under the protective braiding provide electrical insulation. They can be used both for protection against frost and for maintenance temperature applications. Selection chart Supply voltage max. If the temperature falls below the minimum setting, the autocontrol opens the circuit but closes again on temperature rise.
The system is easy to plan and configure. All details about electrical explosion protection mentioned in this certificate are for information only. Mounting plates and brackets in stainless steel The set serves to join two cold leads or to form two heating tape connections. Structure The heater plate consists of a thin, anodised aluminium baseplate, vulcanised with silicone-impregnated glass-fibre mats with an embedded heating coil.
The terminals can accommodate conductors with a cross section of up to 2.
At high temperatures, the heating capacity is reduced to a minimum heating output, which ensures that the limit temperature of the respective temperature class cannot be exceeded. The special design of the aluminum profile facilitates an even temperature distribution in the interior of housings and cabinets. The use of high-quality, corrosion-proof material guarantees the application of the systems even under extreme conditions as, for example, prevail in the chemical industry, petrochemical industry and waste incineration plants.
LEDs display the bus status messages and fault signals. The temperature class can be specified: The Easy Start-up function makes this extremely user-friendly. You can choose either a version with a cast rubber cord or one kkema is directly mounted to an Ex terminal box.
See System Description for the Installation Instructions. One device regulates up to 24 heating circuits safely and reliably. Function The thermostat located in the connection cable keeps the inside temperature in the required range and reliably prevents overshooting the permissible ambient temperature of the heater.
The electrical connection is set up through terminal screws on the rear. Function The load and residual current monitor constantly checks the entire heating system and ensures that the heating cables and temperature sensors always function reliably. The voltage is supplied to the control device through an integrated power supply unit with wide-range voltage.
The pliable part of the resistance thermometer starts after atfx mm. Attex directly connected self-limiting heating circuit considerably reduces the number of junction atsx and installation cost.
Higher switching currents or 3-phase applications are switched by means of a contactor.
kema 08 atex pdf – P(1) –
Up to three phases and the total current can be monitored for each heating circuit. Alternatively, inputs and outputs can be programmed locally through the clearly organised and user-friendly control menu. TAED This is to certify: A special version is also available with a flange fixing.
Our products and solutions provide the highest safety standards and have been tried and tested in many applications all over the world. Fields of application Computer centres, telephone exchanges, libraries, museums, archives, book stores, clean air rooms, air-conditioning and heating centres, etc.
Technical data | Heating Technology
Cable Gland brass The enclosures are available with the necessary cable glands resp. This reduces the programming work to a minimum. Technical data subject to change without notice. The quantity of heat is dependent on the resistance value of the heating cable and the supply voltage.
The heating circuits are activated through an integrated triac then. They reliably ensure that no malfunctioning through leakage current in electrical components, or other disturbances through corrosion formation on mechanical installation parts, can occur. No claims for damages arising from alterations, errors or misprints shall be allowed.
Mounting plates and brackets in galvanised steel The heating circuit end is closed in each case with a heat shrinkable end cap. Function The application of a supply voltage to the resistance cable generates heat.
The heating tape is cut and terminated directly on the construction site according to the circumstances.